Read This First!!!!!
Fax Tone Detection-This
feature, when activated, tells The Stick to detect the presence of CNG/fax
tones which may be transmitted by a calling fax machine or PC Fax card.
All calls accompanied by CNG tones, whether they be from a fax machine
or PC Fax card, are routed through to equipment connected to the device
port labeled FAX.
If no fax-type equipment is used on The Stick, simply deactivate this
feature.
Factory preset is "on".
Protected Hook
Flash-This feature allows The Stick to be compatible with certain
multi-line KSU phone systems.
Some KSU systems do not allow touch tones (DTMF tones) to be generated
from a telephone key pad after an inbound call has arrived.
With Protected Hook flash "on" the phone system can be "fooled"
into generating touch tones by striking the flash key Calls can then be
manually transferred between devices by dialing the proper security access
code.
Factory preset is "off."
Unanswered Call
Silent Transfer-This feature was engineered for those of you who
may receive manual fax or modem calls after normal business hours but
do not use an answering machine.
Manual fax calls (not accompanied by CNG fax tones) and modem calls
usually wind up routed to the phone when the caller cannot execute the
proper access code.
With Unanswered Call Silent Transfer "on", the inbound call
(routed to the phone) will be switched over to a designated port (see
Silent Transfer Destination) after the unanswered phone has been rung
the maximum number of rings.
Factory preset is "off."
Answering Machine
Silent Transfer-This feature works like Unanswered Call Silent
Transfer except that it is designed for calls of 45 seconds or less.
It should only be activated when you are using an answering machine
to field after-hours calls. When a manual fax or modem call arrives and
the answering machine has answered, the caller will still be able to get
to a destination device by staying on the line after the answering machine
"times out".
If you answer a call and hang up before 45 seconds, The Stick will
transfer the call to the designated device.
Factory preset is "off."
Silent Transfer
Destination-After activating either Silent Transfer feature, you
will want to tell The Stick where to route the call.
The "Destination" program feature gives you the option of
routing all after-hours calls to either the fax or modem.
Factory preset is to the port labeled "FAX".
Programmable
Security Access Codes (SAC's)-Transfer of a call is executed by
dialing the programmed SAC for each voice/data device connected to The
Stick.
SAC's are programmable (using a touch tone phone only) up to 4 characters
long-digits 0 through 9 and symbols * Touch Tone Pulse Dial (star) and
# (pound). The Stick will not detect SAC's dialed from "calling"
pulse phones-only from touch tone phones.
Call transfers dialed by a pulse phone are limited to phones hooked
to or on the same line as The
Stick and are limited to transfer to the "FAX" port only.
The pulse dial SAC for this is fixed at "2" You must also
have the "Pulse Select"
feature on if you use a pulse dial phone to transfer a call.
1 Digit Security Access Codes ARE NOT recommended. (Refer to "Programming" Section).
DO NOT use the codes "9" "#","# #", or anything beginning with "9" or "##" These codes are reserved for the "Call Grab" feature and programming access to The Stick, respectively.
DO NOT select an access code that may be the first part of a dialed number or the control code of your answering machine.
Factory preset Security Access Codes are as follows:
Touch Tone |
Pulse Dial | |
Voice 1 and Voice 2 Ports |
*1 |
None |
FAX Port |
*2 |
2 |
Modem Port |
*3 |
None |
Pulse Detection-The
Pulse Detection feature, when activated, allows The Stick to detect the
factory preset code "2" and "Call Grab" preset code
"9" when dialed from a pulse dial phone.
The factory preset for this feature is "off."
Rings To Answer-This
feature directs The Stick to answer an inbound call after a programmed
number of rings (0 to 10 rings) from the phone company.
If RTA is programmed to "O", The Stick will answer the call
during the first ring. Extension phones elsewhere in your location will
only "chirp" the first ring before going quiet.
If the RTA is greater than "0" The Stick will allow all incoming
calls to ring extensions and devices connected to the ports labeled VOICE
1 and VOICE 2 for the programmed number of rings.
Factory preset is 0 rings.
Call Override-
With Call Override "on"-when The Stick "answers" a
call and you pick up an extension more than one second later, The Stick
will recognize the lifting of the handset and stop transmitting ring back
tone to the caller. You can immediately begin to talk or (within 15 seconds)
transfer the call to another device.
In some areas of the country, your local telephone company's lines
and switching equipment may cause this feature to not function properly.
Just deactivate the feature. (See the "Call Grab" feature explanation
in the Standard Features section for another option to Call Override.)
Factory preset is "off."
Maximum Rings-This
feature allows you to program the number of rings transmitted to your
phones/answering machine, fax and modem by The Stick.
Maximum Rings can be programmed anywhere from 4 rings (minimum) to
up to 30 rings. Factory preset is 8 rings to all equipment.
Unrestricted
Manual Transfer- With the UMT
feature "off," The Stick will only allow a manual transfer to
be done during the first 15 seconds of an inbound call when answered from
an extension.
The UMT feature, when activated, enables a transfer to be executed
from an extension phone and by either party at any time during the call,
no matter if the call is inbound or outbound.
Of course, inbound calls answered by equipment through the VOICE 1
or 2 ports may be transferred at any time using the appropriate SAC, regardless
of the setting for this feature.
Factory preset is "on."